Skip to main content

What should I do if the wood pellet machine is blocked?

 The wood pellet machine can be said to be a relatively common mechanical equipment now, which occupies a very important position in our production and life. What if the wood pellet machine is blocked during use?

If you want to know the solution, you must first find the reason. The main reasons for the blockage of the wood pellet machine are as follows:

1. One is that the raw materials used for production contain impurities, such as nails, bricks, etc. The solution is to first turn off the equipment, then open the mold cover, loosen the inner mold nut, then pour out the extruded raw materials, remove the nails or bricks and other impurities contained in it, and then tighten the nut.

2. In the production process of the wood pellet machine, the wood pellet machine is blocked due to wet raw materials or excessive particle size, and it is very difficult to manually clear the blockage. For new friends who have just invested in the wood pellet production industry, this is a headache. Generally large manufacturers will purchase special punching equipment.

3. In the production process, due to power failure or other reasons, the mold is blocked, especially the small hole mold is very difficult to clean. The tool for dredging small-aperture molds is more commonly an electric drill, but this kind of tool wastes time, easily damages the smoothness of the mold hole, and also affects work efficiency. A more effective method is to use oil to boil the ring mold, that is, use an iron oil pan, put the waste oil, put the plug mold, so that the plug hole is completely immersed in the oil, and then heat the bottom of the oil pan until the material in the plug hole bursts Sound, remove the clogged mold, reinstall the machine after cooling, adjust the gap between the mold rolls, according to the operating requirements of the pelletizer, you can quickly clean the clogged mold material by re-driving.

If you have any other questions, please consult the professional pellet equipment manufacturer-RICHI Machinery

Comments

Post a Comment

Popular posts from this blog

How to adjust the gap between the pressure roller of the biomass pellet making machine and the ring die?

  The gap between the pressure roller and the ring die is one of the important parameters adjusted during the operation of the biomass pellet making machine . The adjustment process is also one of the important adjustment steps before the operation of the biomass pellet making machine. The rationality of the gap adjustment will directly affect the use of the biomass pellet making machine. Correct adjustment can save the cost of biomass pellet making machine and improve economic benefits. This article introduces 5 kinds of small knowledge about the adjustment of the gap between the pressure roller and the ring die of the biomass pellet machine:   In general, the rotation direction of the biomass pellet mill ring die is clockwise. For a biomass pellet machine equipped with two rollers, the largest eccentric flange of the left roller should be installed in the upper left half of the ring die when the roller is installed. Zone, the largest eccentric flange of the right press rolle...
Post a Comment
Read more

Common faults and maintenance methods of biomass pellet making machine

  The normal operation of the biomass pellet making machine can ensure the production efficiency, so the daily maintenance and maintenance of the biomass pellet making equipment is very important. Due to the long-term operation of the biomass pellet making machine, various failures will inevitably occur, which requires us to accumulate a wealth of experience in troubleshooting for a long time. The following is the maintenance method of our factory for the common faults of the biomass pellet making machine for your reference. Raw materials cannot enter the pelletizing room   Cause of issue: The conditioner is blocked or the feed port is arched Failure of the feeder auger transmission The feeder auger is blocked  Repair method: Clear the conditioner or feed port Check the feeder auger drive device and troubleshoot Clean the material on the feeder auger  There are raw materials entering the granulation chamber but no granules can be pressed Cause of issue: Die hole blo...
Post a Comment
Read more

It is not recommended to buy a small wood pelletizer.

When customers buy wood pelletizer, we generally recommend choosing large ones instead of small ones, because larger models are more stable and durable. why? Let's start with the principle of the wood pelletizer. The principle of the wood pelletizer is that the pressure wheel strongly squeezes the sawdust through the holes of the die to form sawdust pellets. If you replace the abrasive tool or the pressure wheel with wood, can you still make pellets? Obviously not, then go a step further, the mold pressing wheel is made of iron, can it work? Certainly not. The larger the size of the wood pelletizer, the larger and thicker the grinding wheel, the greater the rigidity and strength of the overall model, while the strength of the raw wood chips is unchanged, so the larger the equipment, the more "labor-saving" it is to press, and the stability of the equipment The better the performance, the longer the service life. As the equipment increases, the processing difficulty of th...
Post a Comment
Read more